January 3, 2005

Innovative Gear Controls for Jenny McCall

The Jenny McCall nearing completion at Gulf Craft.

This January Gulf Craft of Patterson Louisiana will deliver the latest Seacor Marine crew boat the 180x32-foot Jenny McCall. Seacor Marine, with input from the father son team of Norman and Joe McCall, is noted for innovation in this highly competitive market segment.

In keeping with this reputation the Jenny, powered by four 1800 HP Cummins KTA50 M2 main engines, will be equipped with the latest version of CSP Electronics controllable speed propulsion. The system allows the operator or the dynamic positioning system to achieve very precise shaft RPM against a constant engine RPM. The engines on the Jenny turn into Twin Disc 6848 gears with a 2.93:1 reduction. With the engines idling at 750 RPM, this equates to the 52x53-inch props turning at about 250 RPM. If all four engines are locked in at that RPM the boat will be traveling at seven knots. Even with just two engines and the idle set at 650 RPM, the DP system is working extremely hard with constant shifting forward and reverse to hold the vessel in position under a rig when handling cargo.

The Jenny's retractable azimuthing bow thruster. An additional piece will be added
to fair it into the hull when in the raised position.

With the slipping gear, the shaft RPM can be reduced on a continuous scale from 240 RPM to 50 RPM. This allows for quiet steady handling with a smooth transition to lock up and then, at just over the 750 RPM idle, the turbo will kick in for maximum power. "While operation is sometimes compared to that achieved with a trolling gear there are major differences in accuracy, speed of response, gear protection, and heat rejection," maintains CSP Inc. engineer Ray Hatton, "Normally when a fisherman uses a trolling gear the vessel is moving through the water, when a boat is using our system in a dynamic positioning mode they are relatively still in the water so it is more like a bollard pull situation."

Such conditions make additional cooling demands on the system, but Hatton explains they have allowed for this. He also maintains that the computer controlled system is so precise that it can control within plus or minus two RPM on the shaft. "In 2-4-foot seas shafts may hold the vessel without going over the 240 RPM lock-up point, so the engines are sitting there idling at only 750 RPM. Some captains on the four other Seacor boats that have this system, report that in calm weather the system allows them to hold position with only two engines."

Fitting one of the boat's 53x53-inch props.

Joe McCall explains that on the boats with this system, "Due to the constant speed of the engines while maneuvering, we have seen a reduction in the engine repairs. Constant acceleration / deceleration of the engines while maneuvering increases the thermal cycling of the engine as the vessel maneuvers. CSP has allowed us to run the engines at constant speed so we have reduced the wear on the engines. We have also seen a significant reduction in fuel consumption as CSP allows us to maintain position using less horsepower than conventional propulsion systems. This saves our customers money."

The system is tied in with the vessel’s CSP Inc. integrated electronic controls These provide a full vessel monitoring system that allows all alarms and indicators to be integrated into a single display. The system will alert the captain with either a visual indication, voice annunciated audible alarm or both. It also has an e-mail capability that can be utilized to notify a shore base of the alarm, and can take immediate control to alleviate the problem if conditions warrant.

As has been the case in the past, the industry will be watching the latest McCall boat, Jenny McCall, for the next generation of operational innovation. And, as has become the norm, the innovation is happening around the people at McCall Boat Rentals, Seacor Marine and Cummins Mid-South.

For further information:

Ray Hatton
CSP Electronics, LLC
7026 Highway
182 East Morgan City,
LA 70380 (985) 397-3189
e-mail: rhatton@iname.com
web page: www.cspelectronics.com

Joe McCall
Operations Manager
McCall Boat Rentals
Seacor Marine
Phone: 337 775 5485
Fax: 318 775 7025
Mobile: 985 397 2314
E-Mail: JmcCall@ckor.com

Calvin Klotz
V-P Marine Division
Cummins Mid-South
110 E. Airline Highway
Kenner, LA 70062
Phone: 504 465 3403
Fax: 504 465 3408
Mobile:504 343 8377
E-Mail: Calvin.B.Klotz@Cummins.com

550-526, 525-501, 500-476, 475-451, 450-426, 425-401, 400-376
375-351, 350-326, 325-301, 300-276, 275-251, 250-226, 225-201
200-176, 175-151, 150-126, 125-101, 100-76, 75-51, 50-26, 25-0

search engine by freefind
personal info